Auburn University Poultry Ventilation and Housing           NPTC - National Poultry Technology Center at Auburn University


 

NEW NPTC Poultry Toolkit APP for Smartphones

Scan QR code with smartphone camera

or search for Poultry Toolkit in App Store

(email keg0037@auburn.edu for questions)

iPhone App QR Code

iphone app

Android App QR Code

android app

 

Minimum Ventilation Calculator for Smart Phones

 

Minimum Ventilation Calculator Instructions/Computer or Download Version

Start and Run Capacitors for Electric Motors

 

farm workers checking our an eletric motor

Electrical motors are an integral part of a poultry farm operation. They drive ventilation fans, heater blowers, stir fans, feed bin and feed line augers, lift systems for feed and water lines, and actuators for tunnel and vent doors. A two-house (66 × 600 feet each) poultry farm, for example, has over 80 electric motors comprised of 48 fan motors, 16 feed line auger motors, 4 feed fill auger motors, 4 tunnel door/curtain machine motors, 4 vent machine motors, and others.

We see and hear of the challenges producers face in swapping out electric motors (figure 1) when they "go bad" and stop working. The cost of replacing a farm motor can range between $200 and $500-plus depending on the type of motor, size, and brand name. The motor can take 1 to 2 hours to replace depending on how easy it is to remove attached equipment, such as pulleys and shafts, and rewire and attach the new motor.

Click here to read the publication, ANR-2784 - Start and Run Capacitors for Electric Motors.

 

NPTC Tools of the Trade: Testing a Motor Capacitor

 

valve layout Learn the necessary steps to properly test a motor capacitor on the farm.

Before testing can begin, you need to gather the necessary tools to perform a capacitor test:

  • Electrical multimeter with modes to test continuity and capacitance. Continuity will be identified as a sound logo, and capacitance will be identified with a capacitor logo (-||-) on the multimeter dial.
  • Capacitance meter to check the capacitance of a start or run capacitor.
  • Multi-tool driver or set of sockets to open the capacitor housing on the motor.
  • Insulated pliers to remove the spade connectors from the capacitor tabs and to hold the discharge resistor.
  • Electrical resistor (15 to 20k Ohm) to dissipate the electrical charge of the capacitors. An electrically insulated screwdriver is used by electricians to discharge the capacitor, but it is not a recommended method.
  • Soldering iron (electric or gas pen) to remove and reattach a bleed-off resistor if attached to the start capacitor.

Click here to read the publication, ANR-2783 - NPTC Tools of the Trade: Testing a Motor Capacitor.

 

Do Your Valves and Hose Bibs Restrict Water Capacity?

 

valve layout

As we repair or add on to our existing water supply systems, we often don't think about the types of fixtures and valves we use. We often choose replacement valves from what is available on the farm or what is cheapest from the supply store. This publication provides information for making educated choices for your poultry house plumbing.

In the summer months, water capacity always becomes a concern for commercial broiler growers as bird consumption and evaporative cooling systems tax farm water supplies. As we repair or add on to our existing water supply systems, we often don't think about the types of fixtures and valves we use. We often choose replacement valves from what is available on the farm or what is cheapest from the supply store. Figure 1 shows the water panel of a 40-by-500-foot commercial broiler house with yellow arrows highlighting 15 valves or hose bibs. This manifold has 10 PVC and 3 brass ball valves and 2 brass quarter-turn hose bibs, which begs the question: is it safe to assume that the flow rate out of these valves is the same?

Click here to read the publication, ANR-2721 - Do Your Valves and Hose Bibs Restrict Water Capacity?

 

feedback button

Your feedback is important to us. Feel free to send us an email and tell us what you think about our website!

Mission: Improve bottom line profitability of the live production sector of the US poultry industry by providing timely applied research and education resulting in increased efficiencies in housing, equipment, energy and environmental control. Poultry housing, energy, ventilation, economics, and management problems are usually intertwined and very complex.  In trying to find solutions to these major grower and industry problems, we at Auburn University have successfully used a teamwork approach for several years. 

The Auburn NPTC Poultry Housing Team collaborating in this work includes Jeremiah Davis - Director & Research Ag Engineer, Jesse Campbell - Poultry Housing Specialist, Kelly Griggs - Research Engineer II. Feel free to contact any team member if you have questions relating to their areas of expertise. Please note, however, that team members cannot provide design recommendations or diagnose specific problems through email.

Email Jess Campbell for questions concerning this website.

Auburn University      ACES      ACES     

© 2006 - Alabama Cooperative Extension System · All Rights Reserved · Legal Disclaimer